What To Know
- If your Makita drill has a side handle, use a Phillips head screwdriver to remove the screws that secure it to the drill.
- Use a Torx screwdriver or hex key to remove the screws that secure the gearbox to the motor housing.
- The most common reason for a Makita drill to malfunction is due to a buildup of dirt and debris in the motor housing or gearbox.
Disassembling a Makita drill is a straightforward process that can be accomplished with a few basic tools. Whether you’re looking to repair or maintain your drill, this guide will provide you with the step-by-step instructions you need to take it apart safely and effectively.
Safety Precautions
Before you begin, it’s important to take the following safety precautions:
- Unplug the drill from the power source.
- Wear safety glasses to protect your eyes from debris.
- Use a work surface that is clean and well-lit.
Tools and Materials
To disassemble your Makita drill, you will need the following tools and materials:
- Phillips head screwdriver
- Flathead screwdriver
- Torx screwdriver (optional)
- Hex key (optional)
- Soft-bristled brush
- Clean cloth
Step 1: Remove the Battery Pack
If your Makita drill is cordless, start by removing the battery pack. Press the release button on the back of the drill and slide the battery pack out.
Step 2: Remove the Chuck
Use a Phillips head screwdriver to remove the screws that secure the chuck to the drill. Once the screws are removed, pull the chuck straight out.
Step 3: Remove the Side Handle (Optional)
If your Makita drill has a side handle, use a Phillips head screwdriver to remove the screws that secure it to the drill. Once the screws are removed, gently pull the side handle off.
Step 4: Remove the Motor Housing Screws
Locate the screws that secure the motor housing to the drill. These screws are typically located on the sides and bottom of the drill. Use a Phillips head screwdriver to remove all of these screws.
Step 5: Separate the Motor Housing
Once the screws are removed, gently lift the motor housing up and away from the drill. Be careful not to damage any of the wires or connectors.
Step 6: Remove the Gearbox
The gearbox is located inside the motor housing. Use a Torx screwdriver or hex key to remove the screws that secure the gearbox to the motor housing. Once the screws are removed, gently pull the gearbox out of the motor housing.
Step 7: Remove the Brushes
The brushes are located inside the gearbox. Use a flathead screwdriver to gently pry the brushes out of their holders.
Step 8: Clean and Inspect
Once the drill is disassembled, use a soft-bristled brush to clean any dirt or debris from the components. Inspect all of the components for any signs of damage or wear.
Step 9: Reassemble the Drill
To reassemble the drill, simply reverse the steps outlined above. Start by inserting the brushes into their holders and securing them with the flathead screwdriver. Then, insert the gearbox into the motor housing and secure it with the Torx screwdriver or hex key. Next, place the motor housing back on the drill and secure it with the Phillips head screws. Finally, reattach the side handle (if applicable), the chuck, and the battery pack.
Troubleshooting
If you encounter any problems while disassembling or reassembling your Makita drill, refer to the following troubleshooting tips:
- If you are unable to remove the chuck, try using a penetrating oil to loosen the screws.
- If you are unable to remove the motor housing, check to make sure that all of the screws have been removed.
- If you are unable to remove the gearbox, try using a rubber mallet to gently tap it loose.
Wrapping Up: Success in Disassembling Your Makita Drill
Congratulations! You have now successfully disassembled your Makita drill. By following these step-by-step instructions, you can now safely and effectively repair or maintain your drill. Remember to always take the necessary safety precautions and use the appropriate tools for the job.
Questions You May Have
Q: How often should I disassemble my Makita drill for maintenance?
A: It is recommended to disassemble and clean your Makita drill every 6 months to 1 year, depending on the frequency of use.
Q: What is the most common reason for a Makita drill to malfunction?
A: The most common reason for a Makita drill to malfunction is due to a buildup of dirt and debris in the motor housing or gearbox.
Q: Can I use a different type of screwdriver to disassemble my Makita drill?
A: Yes, you can use a different type of screwdriver, but it is important to use the correct size and type of screwdriver to avoid damaging the screws.
