What To Know
- Replacing a Whirlpool dishwasher pump is a relatively straightforward task that can be completed in a few hours with the right tools and a bit of know-how.
- If the dishwasher is making unusual noises, ensure the impeller is properly attached to the pump motor.
- Replacing a Whirlpool dishwasher pump is a manageable task that can save you the cost of hiring a professional repair service.
Are you facing a dishwasher that’s not draining or making strange noises? It might be time to replace the pump. Replacing a Whirlpool dishwasher pump is a relatively straightforward task that can be completed in a few hours with the right tools and a bit of know-how. In this comprehensive guide, we’ll walk you through the process step-by-step, ensuring a successful repair.
1. Replacement Whirlpool dishwasher pump (compatible with your model)
2. Screwdriver
3. Pliers
4. Wrench
5. Bucket or pan
6. Towels or rags
7. Flashlight (optional)
Step-by-Step Guide:
1. Prepare the Dishwasher:
1. Unplug the dishwasher from the power outlet or turn off the circuit breaker that supplies power to it.
2. Turn off the water supply to the dishwasher by closing the valve under the sink.
3. Open the dishwasher door and remove the bottom rack.
2. Access the Pump:
1. Locate the access panel at the bottom of the dishwasher. It’s usually secured with screws.
2. Remove the screws and carefully remove the access panel.
3. You should now see the pump assembly, which consists of the pump motor, impeller, and housing.
3. Disconnect the Pump:
1. Identify the hoses connected to the pump. There will be an inlet hose and an outlet hose.
2. Use pliers to loosen the hose clamps and disconnect the hoses from the pump.
3. Place a bucket or pan underneath the pump to catch any water that may leak out.
4. Remove the Old Pump:
1. Locate the screws or bolts securing the pump to the dishwasher.
2. Use a screwdriver or wrench to remove the screws or bolts.
3. Carefully remove the old pump from the dishwasher.
5. Install the New Pump:
1. Take the new pump and position it in place of the old one.
2. Secure the new pump with the screws or bolts you removed earlier.
3. Reconnect the hoses to the pump and tighten the hose clamps.
6. Test the Dishwasher:
1. Turn on the water supply to the dishwasher.
2. Plug in the dishwasher or turn on the circuit breaker.
3. Close the dishwasher door and select a short wash cycle.
4. Observe the dishwasher as it fills with water and drains.
7. Reinstall the Access Panel:
1. Once you’re satisfied that the dishwasher is working properly, turn it off.
2. Reinstall the access panel and secure it with the screws you removed earlier.
3. Replace the bottom rack in the dishwasher.
8. Final Checks:
1. Check for any leaks around the pump and hoses.
2. Make sure the dishwasher is draining properly.
3. If everything is in order, you’ve successfully replaced the Whirlpool dishwasher pump.
Troubleshooting Tips:
1. If the dishwasher is still not draining after replacing the pump, check the drain hose for clogs or kinks.
2. If the dishwasher is making unusual noises, ensure the impeller is properly attached to the pump motor.
3. If you’re unsure about any step in the process, refer to your dishwasher’s user manual or consult a qualified appliance repair technician.
Conclusion: Achieving Dishwasher Success
Replacing a Whirlpool dishwasher pump is a manageable task that can save you the cost of hiring a professional repair service. By following the steps outlined in this guide, you can restore your dishwasher to its optimal performance and enjoy sparkling clean dishes once again. Remember, regular maintenance and proper usage can extend the lifespan of your dishwasher and prevent future issues.
