What To Know
- Replacing the diverter motor is a relatively simple task that can be completed in under an hour with the right tools and a bit of know-how.
- – Using the appropriate tool (screwdriver or pliers), carefully remove the screws or clips holding the diverter motor in place.
- – Reconnect the drain hose to the drain pump at the bottom of the dishwasher.
A malfunctioning diverter motor can cause various issues in your KitchenAid dishwasher, such as improper water distribution, incomplete cleaning, or even flooding. Replacing the diverter motor is a relatively simple task that can be completed in under an hour with the right tools and a bit of know-how. This comprehensive guide will walk you through the step-by-step process of replacing the diverter motor in your KitchenAid dishwasher.
Tools and Materials Required:
1. Replacement diverter motor compatible with your KitchenAid dishwasher model
2. Phillips-head screwdriver
3. Flat-head screwdriver
4. Pliers
5. Bucket or bowl for draining water
6. Rags or towels for wiping up spills
7. Safety glasses
8. Gloves
Step-by-Step Guide:
1. Safety First:
– Ensure the dishwasher is disconnected from the power source and water supply.
– Wear safety glasses and gloves to protect yourself from potential hazards.
2. Drain the Dishwasher:
– Place a bucket or bowl underneath the dishwasher to catch the draining water.
– Open the dishwasher door and remove the bottom rack.
– Locate the drain hose at the bottom of the dishwasher and disconnect it from the drain pump.
– Allow all the water to drain out completely.
3. Remove the Dishwasher Door:
– Open the dishwasher door fully.
– Locate the screws securing the door to the dishwasher body.
– Using the Phillips-head screwdriver, remove the screws and carefully detach the door from the dishwasher.
– Set the door aside in a safe place.
4. Access the Diverter Motor:
– Locate the diverter motor assembly inside the dishwasher. It is usually positioned near the bottom of the unit.
– The diverter motor is typically secured with screws or clips.
– Using the appropriate tool (screwdriver or pliers), carefully remove the screws or clips holding the diverter motor in place.
5. Disconnect the Diverter Motor:
– Once the diverter motor is accessible, disconnect the electrical connector attached to it.
– Use pliers to gently pry open the connector if necessary.
– Be careful not to damage the connector or the wires.
6. Remove the Old Diverter Motor:
– Once the diverter motor is disconnected, carefully remove it from its housing.
– Inspect the old diverter motor for any signs of damage or wear.
7. Install the New Diverter Motor:
– Take the new diverter motor and position it in the housing.
– Secure the new diverter motor using the screws or clips you removed earlier.
– Ensure the motor is firmly in place and properly aligned.
8. Reconnect the Diverter Motor:
– Reconnect the electrical connector to the new diverter motor.
– Make sure the connector is securely attached and the wires are properly aligned.
9. Reattach the Dishwasher Door:
– Carefully lift the dishwasher door and align it with the dishwasher body.
– Secure the door using the screws you removed earlier.
– Ensure the door is properly aligned and closes securely.
10. Reconnect the Drain Hose:
– Reconnect the drain hose to the drain pump at the bottom of the dishwasher.
– Ensure the hose is securely attached and there are no leaks.
11. Test the Dishwasher:
– Reconnect the dishwasher to the power source and water supply.
– Run a short wash cycle to test the functionality of the new diverter motor.
– Observe the dishwasher for any leaks or unusual noises.
Conclusion: A Smooth-Running Dishwasher Once Again
By following this step-by-step guide, you have successfully replaced the diverter motor in your KitchenAid dishwasher. With a new diverter motor in place, your dishwasher should now distribute water properly, clean dishes effectively, and operate smoothly. Remember to regularly maintain your dishwasher to ensure its optimal performance and longevity.
